S PUTTY SG – MRO 8001S

Repair of cracks and holes on engine and pump casings, pipes, tanks and other equipment

Resurface of pitted metal surfaces

Repair of damaged shafts and hydraulic rams

In-situ flange repair

High-strength structural adhesive for metal bonding

Creation of irregular load bearing shims and reforming of bearing housings

1. Repair cost at fraction of replacement cost
2. No equipment/Power supply needed
3. Excellent electrical insulation characteristics
4. No VOC’s so it can be applied in confined spaces
5. High compressive strength and extreme chemical resistant to most acids, bases, solvents, and alkalis
6. Good resistance to abrasion, friction reduction and hence ideal for turn-around time
7. The product can be applied to any unlimited thickness onto horizontal or vertical surfaces
8. Efficient alternate method of repair where welding or brazing would be undesirable or impossible
9. Can Repair Intricate shape or forms/thin sections, difficult to weld metals
10. Unlimited cycle of repairs possible
11. Less Labor costs – Avoid assembly/disassembly, Pre Machining/Post Machining
12. Superior adhesion – forms a solid bond to steel, cast iron, Stainless steel, concrete, and clean and abraded bronze, copper, and aluminum
13. No shrinkage, expansion or distortion
14. Can do repairs at In-situ repair, In-Plant, Workshops, Remote areas

1 Kg ( A Part – 0.8 Kg & B Part 0.2 Kg Containers)

For complete safety and handling information, please refer to Material Safety Data Sheets (MSDS) prior to using this product.

CURE

‘MRO 8001S S Putty SG’ hardens in around 2 hours at 21°C at 12.5mm thick. The functional cure time may be reduced by curing at an elevated temperature. Heating can be done with a hot box, heat lamps or other heat sources. Never expose this system to a direct flame.

SURFACE PREPARATION

Apply Only To Clean, Firm, Dry And Well Roughened Surfaces

Brush away loose contamination and degrease with MRO 1011 – Kleaner Degreezer. Use a flame to sweat out oil from deeply impregnated surfaces.

Roughen surfaces by blast cleaning, deeply scoring or grinding.

Stabilize cracks by drilling the extremities. Long cracks should be drilled, tapped and bolted every 3-4 inches.

Vee-out all cracks using a rotary file.

Finally degrease again.

WHERE ‘MRO 8001S – S Putty SG’ SHOULD NOT ADHERE. Brush on a thin layer of Release Agent and allow to dry for 15-20 minutes before proceeding.

MIXING

‘MRO 8001S- S Putty SG ’ is formulated to be a dense mix that can be applied easily to overhead and vertical surfaces without running or sagging. Add the hardener to resin and mix thoroughly on a mixing board using a spatula. Do not mix in the containers.

APPLICATION

For best results, product should be kept and applied at room temperature. ‘MRO 8001S – S PUTTY SG’ can be applied when temperatures are between 13ºC and 52ºC. Spread the putty over prepared surface with a putty knife. Press firmly to ensure maximum surface contact and avoid trapping air. To bridge large gaps or holes use fiberglass, expanded metal or other mechanical fasteners.

Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding PPE, safe use, and physical & health hazards. Safety data sheet is available from MRO INFRA or your local MRO INFRA Channel Partner.

Use in well ventilated areas. Avoid continuous breathing of vapour and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

A shelf life of 3 years from date of manufacture can be expected when stored at room temperature (22ºC) in their original containers.

All used and unused product should be disposed of in accordance with state regulations.

The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended MRO INFRA product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.