RED INSULATION VARNISH KOTE – MRO 1006

Avaiability: In Stock
SKU: MRO 1006

‘MRO 1006 – RED INSULATION VARNISH KOTE’ provides a tough industrial strength oil and waterproof coating to insulate electrical equipment and components.

  • The flexible nature of ‘MRO 1006 – Red Insulating Varnish Kote’ in a cured film, provides insulating protection while allowing for heat expansion and contraction and is highly resistant to oils, moisture, and temperature fluctuations.
  • Penetrates, coats, insulates & seals in one step “in-situ”
  • Dries to the touch in 10 minutes & to handle in 45 minutes.
Request a Quote

Electric motors
Coils
LT bus-bars
frayed insulation
LT & HT insulators…. anything that can be spray coated can be insulated & protected.

Imp. Note: For the Best Enhancing of “IR” values, removal of already penetrated moisture (Via Heat Lamps / MRO 1024 – H2O Displazer & MRO 1004 – Electrik Motor Kleaner) is first necessary.

  1. The flexible nature of ‘MRO 1006 – Red Insulating Varnish Kote’ in a cured film, provides insulating protection while allowing for heat expansion and contraction and is highly resistant to oils, moisture, and temperature fluctuations.
  2. Penetrates, coats, insulates & seals in one step “in-situ”
  3. Dries to the touch in 10 minutes & to handle in 45 minutes.

500 ml Aerosol Can

Contains flammable solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation

Shake can well before use. Clean thoroughly and dry the surface to be coated before application of this coating. Mask area not to be sprayed. Spray from 12-15 inches away in light, even coats with a sweeping action of the hand. Allow solvents to evaporate completely before reapplication. Additional coats for heavy film can be applied when first coat is dry. Coating becomes dry to touch in about 20-30 minutes. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.

Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding PPE, safe use, and physical & health hazards. Safety data sheet is available from MRO INFRA or your local MRO INFRA Channel Partner.

Use in well ventilated areas. Avoid continuous breathing of vapour and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

24 months from date of manufacture

All used and unused product should be disposed of in accordance with state regulations.

The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended MRO INFRA product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Additional information

Brand

Application

, , , ,

Industries

,

Available Packaging

Packaging Type

Shelf Life

Caution

Type_

Adhesion

Color

Colour Fastness

Percent Solids (By Weight)

Odour

Specific Gravity

Flash Point

Drying Time -To Touch

Drying Time -To Handle

Drying Time - Full Cure

Drying Time - Recoating Period

Resistant to

Temperature Range

Evaporation Rate

Vapour Pressure (air=1)

Dielectric Strength

Dry Film Thickness (DFT)

Coverage

Propellant

Downloads

Click to Download TDS: MRO 1006 – Red Insulation Varnish Kote

Click to Download MSDS:  MSDS MRO 1006 – RED INSULATION VARNISH KOTE

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.