KLEAR KOTE – MRO 1023

1,256.00

Avaiability: In Stock
SKU: MRO 1023

‘MRO 1023 – KLEAR KOTE’ provides a tough, transparent coating to a variety of surfaces.

  • Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences
  • Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow
  • Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits
  • Prevents sparking and corona discharges
  • Non-conductive and has good dielectric properties
  • Excellent resistance to weak acids & alkalis, water, oils and chemical fumes
  • Easily solderable and very convenient for onsite repair jobs
  • Conforms to requirements of specifications MIL-I-46058C

High Gloss Fast Drying Flexible Acrylic Conformal Coating

‘MRO 1023 – KLEAR KOTE’ provides a tough, transparent coating to a variety of surfaces. Creates a protective, yet smooth, lustrous finish. It is an excellent weatherproof coating that provides long-lasting protection against wear, handling, and oxidation.

Applications

Insulation and protection of all electrical, electronic and high-tech equipment of general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.

Use on brass fixtures, tubing, machine parts, whenever a protective film can be used to prevent oxidation.

It will adhere to metals, wood, and paper.

Benefits

  1. Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences
  2. Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow
  3. Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits
  4. Prevents sparking and corona discharges
  5. Non-conductive and has good dielectric properties
  6. Excellent resistance to weak acids & alkalis, water, oils and chemical fumes
  7. Easily solderable and very convenient for onsite repair jobs
  8. Conforms to requirements of specifications MIL-I-46058C

Available Packaging

500 ml Aerosol Can

Caution

Contains flammable solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Directions of Use

Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 15 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.

Handling

Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding PPE, safe use, and physical & health hazards. Safety data sheet is available from MRO INFRA or your local MRO INFRA Channel Partner.

General

Use in well ventilated areas. Avoid continuous breathing of vapour and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

Shelf Life

24 months from date of manufacture.

Disposal

All used and unused product should be disposed of in accordance with state regulations.

Limited Warranty

The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended MRO INFRA product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Additional information

Brand

Application

, , , ,

Industries

, , ,

Available Packaging

Packaging Type

Shelf Life

Caution

Type_

Appearance

Color

Odour

Specific Gravity

Flash Point

Propellant

Temperature Range

Resin type

Dielectric Constant

Coverage

Drying Time - Full Cure

Drying Time -To Touch

Drying Time -To Handle

Drying Time - Recoating Period

Downloads

Click to Download TDS:  MRO 1023- Klear Kote

Click to Download MSDS:  MSDS MRO 1023 – KLEAR KOTE

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.