Transformer Main Kit – MRO 6004

CONTENT

MRO 8011S – E Putty SG – 1 Kg

MRO 8001S – S PUTTY SG- 1 Kg

MRO 8051 – S Stick – 12 Nos

MRO 1017 – Paint Remover – 500 ml x 2 cans

MRO 1011 – Kleaner-Degreezer – 500 ml x 2 cans

MRO 1020 – Brite Galva – 500 ml x 2 cans

MRO 8020 – Reinforcement Tape – 1 Roll

Nitrile Gloves –  1 Pair

MRO 8011S – E Putty SG

Fast-curing, steel-filled epoxy putty for dependable emergency repairs and quick maintenance work.

MRO 8001S – S PUTTY SG

A two-part high-performance repair composite based on solvent-free epoxy resin reinforced with silicon steel alloy.

MRO 8051 – S Stick

A versatile, hand-kneadable 2-in-1 easy to use epoxy

putty stick.

MRO 1017 – Paint Remover

A fast-acting blend of solvents for the removal of paints, gaskets, adhesives, sealants, lacquers, and varnishes without excessive scraping or causing damage to the surfaces.

MRO 1011 – Kleaner-Degreezer

A non-chlorinated, fast-drying cleaner/degreaser for cleaning oil & grease.

MRO 1020 – Brite Galva

A high-performance zinc coating designed to provide true galvanic corrosion protection to Transformer Fins and stop rusting and rust creepage.

CURE

MRO 8011S – E Putty SG

A 12.7mm thick section will harden at 21ºC in 1 hour.

MRO 8001S – S PUTTY SG

It hardens in around 2 hours at 21ºC at 12.5mm thick. The functional cure time may be reduced by curing at an elevated temperature.

Oil leakages in transformers, capacitors & reactors

Leakage from welded joints

Leakages in pipelines/tanks/compressed air/gas/chemicals

Protects from Bi-metallic Corrosion in Transformer Fins.

MIXING

MRO 8051 – S Stick  – To be cut as per requirement and then mixed by kneading with hand.

MRO 8011S – E Putty  SG–Add Part B to Part A and mix thoroughly on a mixing board using a spatula. Remember you only have a 3-minute pot life so mix for 1 minute.

MRO 8001S S Putty SG – Add Part B to Part A and mix thoroughly on a mixing board using a spatula.

APPLICATION

After surface preparation cut out the required amount of MRO 8051 – S Stick with a knife and knead with fingers or briskly roll between palms to a uniform color.

Apply to the surface to be repaired within 3 minutes of mixing.

Force the material into any cracks or holes to be filled.

If leakage is difficult to be arrested with MRO 8051 – S Stick then another option is to cut as per requirement MRO 8020 – Reinforcement Tape & saturate it with mixed MRO 8011S – E Putty SG & try to plug the leakage with it.

On hardening inspect the area to ascertain leakage stoppage.

Overlay the repaired area with MRO 8011S – E Putty SG.

On hardening of ‘MRO 8011S – E Putty SG’ lay it with ‘MRO 8001S  – S Putty SG’ on the repaired area & its adjoining area with a spatula.

Use MRO 8020 – Reinforcement Tape for additional reinforcement if required.

Proper surface preparation is essential to a successful application. The following procedures should be considered:

1. Pinpoint the leakage area.
2. All surfaces must be dry, clean, and rough.
3. If the surface is oily or greasy use ‘MRO 1011 Kleaner Degreezer’ to degrease the surface.
4. Remove all paint by using ‘MRO 1017 – Paint Remover’,
5. Remove rust and grime from the surface by mechanical techniques.
6. Provide a “profile” on the metal surface by roughening the surface. This should be done ideally by Emery Paper (8-40 mesh grit)