BRUSHABLE CERAMIC – MRO 3004

3,953.00

Avaiability: In Stock
SKU: MRO 3004

‘MRO 3004 – SUPER GLIDE’ two part epoxy Coating designed to improve efficiency of pumps, pipes, valves and othe fluid handling equipment while protecting them from the effect of erosion and corrosion.

  • Excellent chemical resistance against a wide range of chemicals.
  • Long term erosion & corrosion protection
  • Excellent bonding to metal including stainless steel, duplex steels, carbon steels, aluminium, cast iron & bronze as well as specialist alloys of other materials.
  • Excellent Barrier for immersion or splash zone & submerged surfaces
  • Improves the efficiency of pumps, pipes, valves & other equipment.

Coating

‘MRO 3004 – SUPER GLIDE’ two part epoxy Coating designed to improve efficiency of pumps, pipes, valves and othe fluid handling equipment while protecting them from the effect of erosion and corrosion. This high performance product is proven to reduce energy consumption, provide excellent chemical resistance and lower maintenance costs.

Applications

Enhancing performance of centrifugal Pumps & positive displacement pumps.

Protecting pump volutes & impellers from erosion & corrosion

Long term corrosion protection of tube sheets heat exchangers, water boxes & water tanks

Internal pipe coatings to increase fluid flow

Reducing material hang-up in chutes & hoppers

Erosion resistant coating for leading edge protection on wind turbine blades

Benefits

  1. Excellent chemical resistance against a wide range of chemicals.
  2. Long term erosion & corrosion protection
  3. Excellent bonding to metal including stainless steel, duplex steels, carbon steels, aluminium, cast iron & bronze as well as specialist alloys of other materials.
  4. Excellent Barrier for immersion or splash zone & submerged surfaces
  5. Improves the efficiency of pumps, pipes, valves & other equipment.

Available Packaging

1 Kg Container

Caution

For complete safety and handling information, please refer to Material Safety Data Sheets (MSDS) prior to using this product.

Directions of Use

Surface Preparation

 

Proper surface preparation is essential to a successful application. The following procedures should be considered:

 

  • All surfaces must be dry, clean and rough.
  • If surface is oily or greasy, use ‘MRO 2006 NON CHLORINATED KLEANER’ to degrease the surface.
  • All surfaces must be roughened, ideally by grit blasting (3-16 mesh/cm grit size) or by grinding with a coarse wheel or disc. This creates increased surface area and ”edges” to lock into, and essential for successful application.
  • Metal that has been handling sea water or other salt solutions should be grit blasted and high pressure water blasted and left overnight to allow any salts in the metal to ’sweat’ to the surface. Repeat blasting may be required to ’sweat out’ all the soluble salts. A test for chloride contamination should be performed prior to any epoxy application. The maximum soluble salts left on the substrate should be no more than 40 p.p.m. (parts per million).
  • Chemical cleaning with ‘MRO 2006 NON CHLORINATED KLEANER’ should follow all abrasive preparation. This will help to remove all traces of sandblasting, grit, oil, grease, dust or other foreign substances.
  • Heating the repair area to 37ºC – 40ºC immediately before applying MRO 3004 – Super Glide is recommended. This procedure dries off any moisture, contamination or solvents and assists MRO 3004 – Super Glide in achieving maximum adhesion to the substrate.

 

 Mixing

 MRO 3004 – Super Glide is formulated to brush easily onto prepared surfaces with a short bristle brush. Add hardener to resin and mix thoroughly with a spatula or similar tool until a uniform, streak-free consistency is obtained, this should take about 4 minutes. Be sure to mix material from the bottom and sides of container. It is strongly recommended that full container units be mixed

 

Application Instructions:

For best results, product should be kept and applied at room temperature. MRO 3004 – Super Glide can be applied when temperatures are between 15ºC and 32ºC. When temperatures are below 21ºC, cure and pot life will be longer, and above room temperature cure and pot life will be shorter.

Handling

Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding PPE, safe use, and physical & health hazards. Safety data sheet is available from MRO INFRA or your local MRO INFRA Channel Partner.

General

Use in well ventilated areas. Avoid continuous breathing of vapour and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

Shelf Life

3 years from date of manufacture can be expected when stored at room temperature (22ºC) in their original containers.

Disposal

All used and unused product should be disposed of in accordance with state regulations.

Limited Warranty

The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended MRO INFRA product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Additional information

Brand

Application

, , , , , , , , , , , , , , , , , , , , , , , , , ,

Industries

,

Available Packaging

Packaging Type

Shelf Life

Caution

Color

Appearance

Mix Ratio

Pot Life

Cure

Compressive Strength

Tensile Strength

Flexural Strength

Bond Strength

Hardness

Chemical Resistance

Coverage

Specific Gravity

Downloads

Click to Download TDS:  MRO 3004 – Super Glide

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.