PIPE WRAP (50mm X 3.6m) – MRO 8022

Avaiability: In Stock
SKU: MRO 8022

‘MRO 8022 – PIPE WRAP’ is a moisture curing urethane impregnated fiberglass repair composite bandage packed in a hermetically sealed foil pouch.

  • Bonds to most of the substrates
  • Ready to use & versatile
  • Effective & time-saving
  • No mixing and no mess
  • Sets rock hard in minutes
  • Permanent repair
  • Corrosion resistant

Pipe Repair Tape

‘MRO 8022 – PIPE WRAP’ is a moisture curing urethane impregnated fiberglass repair composite bandage packed in a hermetically sealed foil pouch. It is a fast, permanent and instant emergency repair and strengthening system that seals leak even under pressure. ‘MRO 8022 – PIPE WRAP’ not only restores a pipe to its original pressure rating, but actually can make the repair area stronger than the original pipe, reducing downtime, saving in parts and labor. It is excellent on steel, SS, copper, PVC, FRP, HDPE, PP, CPVC, UPVC, clay, concrete, rubber, and more.

Applications

Impact protection

Emergency repair

Corroded pipes

Irregular pipe fittings

Force mains and gravity lines

Joint and tee repair

Underwater repair and splash zone

Benefits

  1. Bonds to most of the substrates
  2. Ready to use & versatile
  3. Effective & time-saving
  4. No mixing and no mess
  5. Sets rock hard in minutes
  6. Permanent repair
  7. Corrosion resistant

Available Packaging

1 No (50mm x 3.6 m) Hermetically sealed foil pouch

 

 

Caution

For complete safety and handling information, please refer to Material Safety Data Sheets (MSDS) prior to using this product.

Directions of Use

SURFACE PREPARATION

Once the leaking area is identified, shut down relevant pipes or hoses immediately wherever possible.

Prepare the surface by cleaning and roughening the pipe to ensure maximum Prepare area atleast 3 times of damaged area.

Put on Nitrile gloves.

Apply MRO 8051-S Stick/MRO 8052 Aqua Stick, knead till uniform consistency, press to fill hole/cracks/voids and hold till leakage The mechanical bond that is created in this step is critical to the performance of the repair system.

 

APPLICATION PROCEDURE

Open foil pouch and immerse MRO 8022 – Pipe Wrap bandage in temperate fresh water for 10 Seconds to activate. The entire contents must be used once the package is opened within approximately 2 minutes.

Apply MRO 8022 – Pipe Wrap around the damaged area extending up to 50mm either side of the leak to ensure complete coverage. It is important that the bandage is applied quickly as curing begins once it is taken out of the water.

Whilst wrapping, pull each layer tightly by using your hand to mould and squeeze the layers together. Continue this action during and upon completion.

The indirect heat may be applied to accelerate cure times if required.

The wrapping should be done minimum 4 times around pipes or 4 times of wall thickness whichever is higher.

Keep working the urethane back into the tape while moulding and pressing the tape until it has lost its initial tackiness.

The higher temperature & chemicals, if within specified limits, do not cause any softening of the bandage.

Temp.

Working Time (Approximate)

Return to Service Time

45°C

1 Min

20 Min

35°C

3 Min

23 Min

21°C

8 Min

28 Min

16°C

10 Min

25 Min

10°C

14 Min

42 Min

6°C 17 Min

184 Min

2°C 20 Min

381 Min

Handling

Read instructions on the container label of the product before use. The product safety data sheet (SDS) contains the relevant information regarding PPE, safe use, and physical & health hazards. Safety data sheet is available from MRO INFRA or your local MRO INFRA Channel Partner.

General

Use in well ventilated areas. Avoid continuous breathing of vapour and spray mist. In closed areas or areas with poor ventilation, use respiratory protection. For complete details on safety, short and long term exposure, refer to this product’s safety data sheet (SDS).

Shelf Life

A shelf life of 2 years from date of manufacture can be expected when stored at room temperature (22ºC) in their original foil pouch.

Disposal

All used and unused product should be disposed of in accordance with state regulations.

Limited Warranty

The information and data contained in this sheet is accurate to the best of our knowledge or is obtained from sources, tests or experiences believed by us to be reliable and accurate. User is responsible for determining whether recommended MRO INFRA product is fit for a particular purpose. All products should be tested for suitability on a particular application prior to actual use. We make no representations of any kind. Data offered without warranty.

Additional information

Application

, , , , , ,

Brand

Available Packaging

Packaging Type

Shelf Life

Compressive Strength

Temperature

, ,

Tensile Strength

Flexural Strength

Lap Shear Strength

Hardness

Max Pressure

Flexibility

Active gravity flow leak

Abrasion Resistance

Downloads

Click to Download TDS:  MRO 8022 – Pipe Wrap (50mm x 3.6m)

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.